Prestige Aluminum Railing Kits Include Square Balusters, Four Rail Connectors, Top, and Bottom Rails, Footblock(s) and Screws. Available in Absolute Black, Cocoa Bronze, Dream White, and Maple Cream. Prestige Rail Kits by DekPro install between posts, and comply with most residential codes, at a finished height of 38".
It is important to measure your post before ordering post caps.
2" cap is not avalible in Gloss White
DekPro Prestige 3"x3" Post Kit
Prestige Post Kits by DekPro are 3"x3" and range from 40" to 54" in Height. Post Kits Include Post with Pre-Welded Base Plate, Post Cap, Post Flair or Skirt, and Shimms. Post Kits easily install with a Jig Installation Tool
Learn more about Prestige Railing Below!
DekPro Prestige Quick Jig Rail Guide
Quick Jig Rail Guide is a bracket setting tool which is designed to fit perfectly against DekPro 3" Posts and 4" Post Sleeves. Dramatically reducing installation time by installing level brackets only with this railing template jig.
TimberTech Evolutions Builder Rail 2x4 Packs
TimberTech Evolutions Builder Rail is a 2pack of composite 2x4's meant to be installed identically to builder-grade style wood 2x4 railing. Use rail packs with - not included: 2x4 Rail Connectors, 3/4" Baluster Connectors and 3/4"x26" Balusters - or - Face Mount Balusters, Posts, Sleeves, and Post Skirts.
Available in Classic Black and Traditional Walnut in 6-foot and 8-foot packs. Download Install Guide and Evolutions Brochure
DekPro Prestige Rail Bracket Kits
DekPro Prestige Bracket Kits or Cut Kits Include 4/pk Rail Connector used with Prestige Style top and bottom rails, Screws, and a Footblock w/connector. Bracket Kits come in Level, Stair, and Multi-Angle Level. Level Kits are used for and level handrail. Stair Kits are used for and raked or stair handrail. Cut Kit may be needed when using Prestige Blank Rails
Messmers UV Plus Wood Deck Stain (for Cedar Wood)
Messmer's U.V. Plus stain for Cedar Decks, Fences, and Siding.
Each gallon covers 100-250 Square Feet, depending on roughness of wood
VOC: Less than 450 grams per liter
Made in the USA
Pro Deck & Patio
TimberTech Evolutions Post Sleeve
Evolutions Post Sleeves by TimberTech fit or sleeve over a nominal 4x4 actually (3.5"x3.5"), use a Post Skirt to hide the bottom of post sleeve (not included) and were designed to allow the rail to run over-the-top of the post and sleeve. Evolutions Post Sleeve is used with Contemporary or Builder Rail and both require an additional top rail to run over the post and sleeve.
Post Sleeves available in 42-inch or 8-foot and in Classic Black or Traditional Walnut.
Westbury Post Kit 2"x2"
Westbury Post Kits include a Post with a welded Flange or base plate, Post Cap and Post Flair, along with Metal Shims, and a Unique easy-to-use leveling system.
2"x2" Westbury Post Kits install to the face or surface of any deck or concrete. Use post kit for all Westbury Aluminum Railing Systems such as C10 Tuscany, C80 VertiCable, or C30 Riviera
Cap and Flair Included in Post Kit.
Each post requires 4 screws for installation. Use wood screws 4" or over for wood surface. Use concrete screws over 3" for concrete surface installation.
Used typically for "cut kits." Each rail pack contains one hardware kit. If the intended use for one section, is to be cut and used in two openings (between posts) then an additional Hardware Kit must be used
Evolution Contemporary Rail Kit includes two Universal Rails, Hardware, Footblocks, and Screws. Available in 6 foot and 8 foot, Classic Black and Traditional Walnut. Kits do not include balusters. Evolutions Contemporary by TimberTech is a modern take on a "deck builder" style rail. Contemporary rail can be installed with regular 29" Aluminum Balusters, Feeney Cable, or even Glass Balusters.
Sleeves, Skirts, and Rail Top Cap sold separately.
Evolutions Installation Guide Above
Evolutions Contemporary with Balusters Installation Video Above
Evolutions Contemporary With Cable Railing Install Video Above
Feeney Threaded Terminal Post Kit Stair
DesignRail Kit (TTS) Threaded Terminal Stair Post Kits by Feeney are tensioning termination posts.Used to begin a cable section and typically positioned at the top of the stairs. Use with QC Stair, and DesignRail Stair Rail Kits. Use TT side of CableRail Kits with Threaded Terminal Posts. Stair angle must be between 29 and 34 degrees. Visit DesignRail Kits Page for literature and installation. Available for 36" Railing only.
DesignRail Kit (TT) Threaded Terminal Level Post Kits by Feeney are termination posts which are required for any level DesignRail Kit cable section. Use TT side of CableRail Kits. Treaded Terminal fittings are the tensioning side of CableRail Kits, and require 3-4 inches behind the post for tensioning purposes. 36" Post Requires 9 Cable Runs, 42" Post Requires 11 Cable Runs.
DesignRail Kit (SR) Series 150 Stair Rail Kits by Feeney are available in 6' Long, Black, 36" Height only. Stair Rail Kit includes an Intermediate Picket positioned in the middle of each section, top and bottom rails, snap cap, and hardware. Series 150 is a Graspable Handrail option. Use 9 runs of 1/8" cable for 36" CableRail Kits sold separately. DesignRail Kits Page for literature and installation, posts, and CableRail Kits. Use with pre-drilled DesignRail Kit Posts or wood posts. Use for stair angle between 29 and 34 degrees.
Stainless Steel End Caps by Feeney are used to cover Treaded Terminal Washers or Quick-Connect fittings in CableRail Kits. SS Caps are the same size as Colored End Caps but are more durable, and only made in stainless steel.
Feeney Single Corner Post Kit Level
DesignRail Kit (SC) Single Corner Level Post Kits by Feeney allow for only one post on level cable turns up to 90 degrees. DesignRail Single Corner Level Posts are pre-drilled and used with 1/8" Cable for a continuous run at any level corner. Must use with Level Rail Kits on either side, as well as QC and TT posts in the cable section. 36" Post Requires 9 Cable Runs, 42" Post Requires 11 Cable Runs.
Feeney Quick-Connect Surface Mount Tensioner #9913
Quick Connect Surface Mount Tensioner #9913 is a Swiveling Cable Receiver which attaches to the face of a wood or metal post (metal screws not included) use for 1/8" Cable and pair with Fixed-End Surface Mount 9903. Includeds 2 screws for mount installation.
Quick Connect Surface Mount #9903 is a non-tensioning fixed-end Cable Receiver which attaches to the face of a wood or metal post (metal screws not included) use for 1/8" Cable and pair with Tensioning Surface Mount 9913. Includeds 2 screws for mount installation.
Quick Connect Pivot Tensioner #9916 is a 1/8" Compatible tension swiveling connector allowing for 3/4" in tensioning adjustment, using a lag for stair rail application. With a wide 180 degree pivoting range for stair application, the lag can be screwed into the post level. Then once the cable is connected an tightened, the angle of all connectors will be consistent along the stairs. Includes 2" Lag for wood posts, and 2-1/2" Lag for Composite Sleeved Posts.
Quick Connect Pivot #9915 is a 1/8" Compatible fixed end connector, using a lag for stair rail application. With a wide 180 degree pivoting range, the lag can be screwed into the post level. Then once the cable is connected an tightened, the angle of all connectors will be consistent. Includes 2" Lag for wood posts, and 2-1/2" Lag for Composite Sleeved Posts.